【英文标准名称】:Aerospaceseries;aluminiumalloyforgingstockandforgings;technicalspecification;part1:generalrequirements;GermanversionEN2082-1/A1:1993;amendment1
【原文标准名称】:航空航天系列.铝合金锻坯和锻件.技术规范.第1部分:一般要求
【标准号】:EN2082-1/A1-1993
【标准状态】:现行
【国别】:
【发布日期】:1993-11
【实施或试行日期】:
【发布单位】:欧洲标准学会(EN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:制造;锻制品;作标记;锻件;定义;规范(认可);航空运输;铸造实践;试验;验收规范;缺陷与故障;合金;铝合金;再熔料;检验;航空航天运输;交货条件;铝
【英文主题词】:Acceptancespecification;Aerospacetransport;Airtransport;Alloys;Aluminium;Aluminiumalloys;Defects;Definition;Definitions;Deliveryconditions;Forgingpractices;Forgingstocks;Forgings;Inspection;Manufacturing;Marking;Remeltingstock;Spacetransport;Specification(approval);Testing;Wroughtalloys;Wroughtproducts
【摘要】:
【中国标准分类号】:V11
【国际标准分类号】:49_025_20
【页数】:3P.;A4
【正文语种】:英语
基本信息
| 标准名称： | 扩口式管接头扩口端尺寸 |
| 英文名称： | Flared couplings - Flared end |
| 中标分类： |
机械 >>
通用零部件 >>
管路附件 |
| ICS分类： |
机械系统和通用件 >>
紧固件 >>
环、套管、管接头、承插
|
| 替代情况： | 替代GB/T 5653-1985 |
| 发布部门： | 中华人民共和国国家质量监督检验检疫总局 中国国家标准化管理委员会 |
| 发布日期： | 2008-05-07 |
| 实施日期： | 2008-11-01 |
| 首发日期： | 2008-05-07 |
| 作废日期： | |
| 主管部门： | 中国机械工业联合会 |
| 提出单位： | 中国机械工业联合会 |
| 归口单位： | 全国管路附件标准化技术委员会 |
| 起草单位： | 中机生产力促进中心、海盐管件制造有限公司、伊顿（宁波）流体连接件有限公司等 |
| 起草人： | 李维荣、耿志学、周舜华、李俊英、陶忠明、左学俊、阮浩丰、周剑飞、王利民、冯峰 |
| 出版社： | 中国标准出版社 |
| 出版日期： | 2008-11-01 |
| 页数： | 8页 |
| 计划单号： | 20064245-T-604 |
适用范围
本标准规定了扩口式管接头扩口端尺寸。
本标准适用于管子外径为４ｍｍ～３４ｍｍ，最大工作压力３．５ＭＰａ～１６ＭＰａ的液压流体传动和一般用途的管路系统。
前言
没有内容
目录
没有内容
引用标准
下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件，其随后所有的修改单（不包括勘误的内容）或修订版均不适用于本标准，然而，鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件，其最新版本适用于本标准。
ＧＢ／Ｔ５６５３—２００８ 扩口式管接头技术条件
所属分类： 机械 通用零部件 管路附件 机械系统和通用件 紧固件 环 套管 管接头 承插
Product Code:SAE J18
Title:Sponge and Expanded Cellular Rubber Products
Issuing Committee:Committee On Automotive Rubber Specs
Scope: The SAE Committee on Automotive Rubber Specifications has concluded, that in light of the fact that SAE J18 is a mirror image of ASTM D 1056 (Vol. 8.01), SAE J18 will be eliminated in the year 2005.This SAE Recommended Practice covers flexible cellular rubber products known as sponge rubber and expanded rubber, but does not apply to latex foam rubber or ebonite cellular rubber. The base material for an open/closed cellular product may be made of synthetic, natural, reclaimed rubber, or a mixture, and may contain other polymers or chemicals, or both, which may be modified by organic or inorganic additives. These elastomeric materials have properties similar to those of vulcanized rubber, namely (a) the ability to be converted from a thermoplastic to a thermosetting state by crosslinking (vulcanization) and or (b) substantial recovery of their original shapes when strained or elongated, or both.Extruded or molded shapes of sizes too small for cutting standard test specimens are difficult to classify or test by these methods and will usually require special testing procedures.In case of conflict between the provisions of this general specification and those of detailed specifications or test methods for a particular product, the latter shall take precedence. Reference to the test methods in this document should specifically state the particular test or tests desired.The values stated in SI units are to be regarded as the standard. English units are included for reference only.The following safety hazards caveat pertains only to the test methods portions of this document: This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.NOTE -- ASTM D 1056-98 and ISO 6916-1 are similar to this document.